PRODUCTS

PNS / BNS
SODIUM POLYNAPHTALENE SULFONATES

Superplasticizers / high efficiency water reducers, the function of these products is to reduce the water content in the mix without reducing its workability, obtaining significant improvements in the initial strengths and durability, increasing the consistency that will result in very fluid concretes without affecting its mechanical properties or strength. They optimize the water / cement ratio in order to obtain a concrete with equal fluidity and equal resistance.

Classification according to European standards UNE-EN 934-2:2010+A1:2012

Nutrisol® DS3
Nutrisol® DS5
Nutrisol® DS10
Nutrisol® DS18

TECHNICAL DATA SHEET SAMPLE REQUEST

PNC
CALCIUM POLYNAPHTALENE SULFONATES

High efficiency superplasticizers / water reducers especially indicated on the production of gypsum wallboard, plasters treatment and precast concrete production. Its low content of sodium sulphates give it a wide dispersing power. They reduce the water content in concrete without reducing its workability, improving strength and durability, increasing consistency, which translates into very fluid concretes without affecting its mechanical properties or durability.

Classification according to European standards UNE-EN 934-2:2010+A1:2012

Nutrisol® Ca

TECHNICAL DATA SHEET SAMPLE REQUEST

PCE
POLYCARBOXYLATE ETHERS

These are the last generation compounds, with great flexibility to modify their structure and obtain certain properties in terms of dispersing capacity, modifying the setting and retention of workability. The water-reducing or fluidizing capacity in this type of polymers is usually higher than that obtained with PNS / BNS. About their effect on concrete and their great capacity and flexibility to meet desired requirements, they are one of the greatest advances in concrete chemistry.

Classification according to European standards UNE-EN 934-2:2010+A1:2012

Nutrisol® PCE
Nutrisol® PCR
Nutrisol® PCE50
Nutrisol® PCR50

TECHNICAL DATA SHEET SAMPLE REQUEST

SMF
SULPHONATED MELAMINE POLYCONDENSATED

Last generation compounds, like PCE, have great flexibility to modify their structure and obtain certain properties in terms of dispersant capacity on plastification and water reduction of cement and calcium sulphate based materials. They are specially recommended on gypsum wallboard production. The water-reducing or fluidizing capacity in this type of compound is higher than that obtained with PNS. They are considered one of the greatest advances in concrete chemistry.

Classification according to European standards UNE-EN 934-2:2010+A1:2012

Nutrisol® SM
Nutrisol® SMD

TECHNICAL DATA SHEET SAMPLE REQUEST

LIGNOSULPHONATES
SODIUM LIGNOSULPHONATE / CALCIUM LIGNOSULPHONATE

Used as water reduction agents in concrete, specially designed to create a plasticizing effect. They additionally present an initial controlled delay on setting time.

Classification according to European standards UNE-EN 934-2:2010+A1:2012

Nutrisol® LC
Nutrisol® LS

TECHNICAL DATA SHEET SAMPLE REQUEST

REDISPERSIBLE POLYMERS

This sophisticated line of RDP are indicated for tile adhesives, renders, plasters and repair mortars. They increases strength of the bond between mortar and surface in the open air and water, heat ageing, and at cyclic freezing thawing. An spray-drying special water-based emulsion, mostly based on vinyl acetate-ethylene (VAC/E), obtained a free flowing organic polymer powder. It will increases the flexibility and adhesiveness of the mortar, gypsum based products and wall putty, extend the opening time, improve the mortar's bending strength, waterproofness, wear resistance and prevent mortar and wall putty cracking. They can effectively improve the flexibility and adhesion.

Classification according to European standards UNE-EN 934-2:2010+A1:2012

Nutrisol® 5010N
Nutrisol® 5044N

TECHNICAL DATA SHEET SAMPLE REQUEST

TECHNICAL INFORMATION

PRODUCT GUIDES – PRODUCT DATA SHEETS – SECURITY DATA SHEETS

© Copyright 2020 MARFRAN - All rights reserved